Installing a Brick Paver Walkway or Decorative Brick Blocks

The usage of Setting up a Brick Paver Walkway or Refractory Fire Brick or Pavers to produce a pathway or patio area matches a house in a method that is unequaled. It adds a level of quality and elegance to a home entrance that can not be achieved with either concrete or asphalt. Brick and Pavers also come in several colors and shapes enabling for distinct color pattern and patterns to be achieved. In addition, installing a Brick or Paver pathway does not necessarily need a pro. With some standard understanding and a fairly simple pathway plan, a property owner is capable of carrying out such a project.

The secret to setting up a Brick or Paver Walkway is to first correctly prepare the area where the bricks/pavers are to be set up. In addition, string lines ought to be strung on each side of the sidewalk.
As soon as the location has been dug down, 3/4" gravel stone need to be laid in and tamped down tightly. Then 2" of sand, or stone dust ought to be spread over the gravel. Again the sand/stone dust must be tamped down. Stone dust is preferred. The height in between the tamped down sand and the stringline should equate to the thickness of the brick or paver.

Now that you have a steady base, place a 1" pipeline or ledger board the length of the pathway on either side of the sidewalk. Then utilizing a flatedge, e.g. a 2"x4" board, slide it over the two lengths of the pipe/ledger board. In doing this you will create a level area to lay the bricks/pavers.

Now place on the level sand/stone dust strips of plastic brick borders. Install a run on both sides of the ready area. These strips will act as your walkway border and help to preserve the stability and shape read more of the sidewalk.

The key to laying the bricks/pavers is to ensure that they interlock with each other. Always stagger adjacent rows of bricks by 1/2 of a brick to interlock them. This will once again assist preserve the integrity of the walkway.

When building the walkway, inevitably bricks/pavers will need to be cut or split. Unless you want to buy or rent a pricey wetsaw, I would suggest purchasing a basic brick/paver splitter. It is essentially a chisel with a large end that is the width of the bricks/pavers. To actually cut/split the brick/paver, lay it in a bed of sand and location the chisel at a 75 degree angle over the spot where you wish to break the brick. Utilizing a hammer strike the butt end of the sculpt strongly. You might need to do this a number of times. You might likewise wish to turn the brick/paver over and strike the other side of the brick utilizing the hammer and chisle. Within one or 2 strikes the brick/paver should break easily. If your pathway has curves you will need to buy/rent a wetsaw.

After setting up the bricks, develop the outdoors edges with extra sand, and then shovel in the topsoil and pack down securely.
Finally, spread stone dust over the new sidewalk and sweep into the fractures. Repeat this process a couple of times to make sure the cracks are fully filled. This will finish the interlocking of the bricks and help to remove any weed development. Just include turf seed to the outside edges and you ought to have a beautiful entryway to your house within a couple of weeks.


In addition, setting up a Brick or Paver walkway does not always require a pro. The key to setting up a Brick or Paver Walkway is to first appropriately prepare the location where the bricks/pavers are to be installed. Now that you have a steady base, position a 1" pipeline or ledger board the length of the walkway on either side of the sidewalk. These strips will act as your walkway border and assistance to maintain the integrity and shape of the pathway. Inevitably bricks/pavers will require to be cut or split when developing the walkway.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 15

Comments on “Installing a Brick Paver Walkway or Decorative Brick Blocks”

Leave a Reply

Gravatar